Definitions:
Boot Disk
- Refers to either a Windows 95 or Windows 98 boot disk. Any other type of boot disk might load memory resident programs which will interfer with the flash process. Make sure you hit the F5 key when the boot disk first starts running to make sure no other programs are loaded in the back ground without your knowledge.
Bios Flash Package
- Unzip the entire bios package to a seperate clean floppy. Insure there are 3 files that are unpacked during the unzip processRequirements:
Two separate diskettes
are needed. The first diskette is the Windows 95/98 Boot Disk. The second diskette should contain the 3 files needed to flash the bios. These files are provided when you unzip the bios
flash package from the website. Procedure:
At the A: prompt simply type in "flash" and the rest will be handled by the files included in your download. |
|
Date |
BIOS |
Description |
|
|
|
TYAN Thunder K8SD Pro (S2882-D) V3.09 New features and Fixes : * Fixed a issue where the system will hang up after rebooting
from RedHat4U2 with dualcore CPU with PowerNOW enabled * Fixed a issue where the FAN1(J44) RPM will be moved up and down if fan power control set as [Enabled]
* Added the patch for Opteron CPU errata #122 * Added the support for M3291 * Added bios chip support for the SST49LF040B Rev.CA Flash-ROM
* Fixed the USB device might not be detected imtermittently after continual reboot |
|
|
|
|
TYAN Thunder K8SD Pro (S2882-D) V3.07 New features and Fixes : * Fixed an issue where if Fan Spreed Control is set to [Enable]
then the RPM is not stable around temperatures of 45°C or lower |
|
|
|
|
TYAN Thunder K8SD Pro (S2882-D) V3.06 New features and Fixes : * Corrected the BIOS datecode * Updated ACPI S4 support
* Fixed an issue with Cherry Keyboards * Fixed an issue with PXL-S30 SCSI Cards where the system would hang in the Option ROM
* Adjusted CPU temp detection method for more accurate CPU temperature display * Updated CPU micro coding for new CPU support
* Updated the Sil3114 SATA Option ROM to v5.0.64 |
|
|
|
|
TYAN Thunder K8SD Pro (S2882-D) V3.05 New features and Fixes : * Added support for 4 Sec delay to the Power Button Mode
options * Fixed an issue where Opteron CPU's were not correctly displaying their temperatures * Added Opteron 280 CPU support * Updated TSO support
* Fixed CPU display for Dual Core CPU L1 and L2 cache sizes * Added BCM F1 option for SMDC of LAN |
|
|
|
|
TYAN Thunder K8SD Pro (S2882-D) V3.04 New features and Fixes : * Updated SMBIOS information
* Fixed an issue where the system will hang during the POST with both the Adaptec SO-DIMM 2015s Raid controller card and SMDC M3289 installed
* Fixed an issue where the Fan speed display wouldn't register correctily if fan power control was set to enabled * Updated BIOSCheck 2.4 support
* Updated CPU temperature display * Added support for SMBIOS Type 38 IMPI information * Updated PowerNow! support for CG stepping CPU's
* Updated the boot loader console redirect support * Changed PowerNow! minimal voltage to v1.35v * Updated the lower FAN RPM registers for proper display
* Updated Opteron 254 PowerNow! support * Updated IOMMU support |
|
|
|
|
TYAN Thunder K8SD Pro (S2882-D) V3.03 New features and Fixes : * Fixed an issue where the Peppercon's USB KVM would
hang in use * Implemented AMD's recommendations for DDR400 speed settings when large loads (more than 4 dimms) were used at once
* Added a Auto detect feature and addded support for the M3289 & M3290 SMDC cards * Implemented AMD erratum 123 * Added a IPMI Over Lan selectable option in the BIOS
[82551]/[BCM5704] * Fixed an issue where Bank Interleaving was not functioning properly * Fixed an issue where AMD PowerNow! was not working
correctly * Fixed an issue where the reported values of CPU1 Vcore & CPU2 Vcore were not correct * Fixed an issue where the use of DualCore CPU's would
not H/W Mem Remap correctly and would fail upon use |
|
|
|
|
TYAN Thunder K8SD Pro (S2882-D) V3.02 New features and Fixes : * This is the first release BIOS. |
|