Thunder LE-T (S2518) Riser Card
| BIOS | CPU | Drivers | FAQ | Memory | S/I | Utility |

  Benefits and Applications

The Thunder LE-T was specifically designed for the Internet infrastructure.  It supports two CPUs; either the Pentium III processor, or the Pentium III processor DP.  With its high-performance ServerWorks chipset, 64-bit PCI bus, and integrated network, storage and video controllers, the Thunder LE-T provides superior performance and a wealth of integrated features.  The Thunder LE-T's most intriguing feature is its form factor.  Utilizing angled memory sockets and a highly integrated design, the Thunder LE-T is the perfect choice for today's 1U/2U servers.

  Thunder LE-T Models

Standard Model

Integrated SCSI

Integrated IDE RAID

UPC Number













  Standard Features

  • Processor
    Dual PGA370 ZIF sockets
    Supports up to two Intel Pentium III Processors or Pentium III Processors with 512kB Cache
    Onboard VRM (VRM 8.5 spec) supports 2 CPUs
    Front-Side Bus support for 100MHz and 133MHz
  • Chipset
    ServerWorks ServerSet III LE3 chipset
    Integrated I/O APIC; OSB4 south bridge
    SMsC FDC37B787 Super I/O ASIC
  • System Memory
    Four 25° angled 3.3v 168-pin DIMM sockets
    Angled sockets enable rackmount installation
    Supports up to 4GB Registered PC133
    Supports ECC (72-bit) memory modules
  • Expansion Slots
    One 64-bit 66MHz (3.3-volt) PCI slot and one 64-bit 66MHz (5-volt) PCI slot.
    3.3-volt slot supports Adaptec 2000S Zero-channel RAID controller
    Total of two usable slots (one if installed in 1U)
    PCI riser card required when installed in 1U/2U
  • Integrated I/O
    One floppy connector supports up to two drives; microfloppy support via optional cable
    Two 9-pin 16550-based serial ports (one via optional cable); one 25-pin SPP/ECP/EPP parallel port via optional cable
    Four USB ports (two via optional cable)
    PS/2 keyboard and mouse ports
  • Integrated PCI IDE
    Dual-channel master mode
    Up to four Enhance IDE devices
    Support for DMA33 IDE and ATAPI-compliant devices
  • Integrated LAN Controllers
    Dual Intel 82559 LAN controllers
    10/100Mbps max. data transfer rate per controller
  • Integrated Video
    ATI RAGE XL graphics controller
    4MB frame buffer (SDRAM)
    Standard 15-pin analog VGA port
  • Integrated IDE RAID (optional)
    Promise FastTrak100 IDE RAID controller
    Dual-channel master mode
    Support up to four Enhanced IDE devices
    Support for UDMA 100/66/33 IDE drives
    Supports IDE RAID levels  0, 1 and 0+1
  • Integrated SCSI (optional)
    Adaptec AIC-7899W controller
    Dual-channel Ultra160 SCSI support
    160MB/sec maximum data throughput per channel; supports up to 15 LVD SCSI devices per channel
  • Hardware Monitoring
    Winbond W83782D hardware monitoring ASIC; CPU temperature, voltage, and fan monitoring
  • BIOS
    AMI BIOS on 4Mb Flash ROM
    Auto-configuration of IDE hard drive types
    Multiple boot options
    DMI 2.0 compliant
  • Form Factor
    ATX footprint  (12" x 9.6", 304.8mm x 243.84mm)
    One 20-pin ATX power connector
    One serial port and one VGA port
    Stacked USB (two) ports
    Side-by-side LAN (two) ports
    Stacked keyboard and mouse ports
  • Regulatory
    FCC DoC (Declaration of Conformity)
    European Community CE (Declaration of Conformity)

 * Due to limitations of the ServerWorks chipset, IDE transfer rates are limited to DMA at 16.6MB/sec.

Information published on is subject to change without notice.
Copyright © , TYAN COMPUTER CORPORATION. All Rights Reserved.