Thunder K8S Pro (S2882) BIOS

  Current BIOS Revisions

Definitions:

Boot Disk - Refers to either a Windows 95 or Windows 98 boot disk. Any other type of boot disk might load memory resident programs which will interfer with the flash process. Make sure you hit the F5 key when the boot disk first starts running to make sure no other programs are loaded in the back ground without your knowledge.

Bios Flash Package -  Unzip the entire bios package to a seperate clean floppy.  Insure there are 3 files that are unpacked during the unzip process

Requirements:

Two separate diskettes are needed. The first diskette is the Windows 95/98 Boot Disk. The second diskette should contain the 3 files needed to flash the bios.  These files are provided when you unzip the bios flash package from the website.

Procedure:

At the A: prompt simply type in "
flash" and the rest will be handled by the files included in your download.

Date

BIOS

Description

08/18/06
 

2882_309

TYAN  Thunder K8S Pro (S2882) V3.09
New features and Fixes :
* Fixed a issue where the system will hang up after rebooting
   from RedHat4U2 with dualcore CPU with PowerNOW enabled
* Fixed a issue where the FAN1(J44) RPM will be moved up and
   down if fan power control set as [Enabled]
* Added the patch for Opteron CPU errata #122
* Added the support for M3291
* Added bios chip support for the SST49LF040B Rev.CA
   Flash-ROM
* Fixed the USB device might not be detected imtermittently
   after continual reboot

07/28/06
 

2882_308

TYAN  Thunder K8S Pro (S2882) V3.08
New features and Fixes :
* Fixed a issue where the system will hang up after rebooting
   from RedHat4U2 with dualcore CPU with PowerNOW enabled
* Fixed a issue where the FAN1(J44) RPM will be moved up
   and down if fan power control set as [Enabled]
* Added the patch for Opteron CPU errata #122
* Added the support for M3291
* Added the support for SST49LF040B Rev.CA Flash-ROM

03/23/06
 

2882_307

TYAN  Thunder K8S Pro (S2882) V3.07
New features and Fixes :
* Fixed an issue where if Fan Spreed Control is set to [Enable]
   then the RPM is not stable around temperatures of 45c or lower

03/13/06
 

2882_306

TYAN  Thunder K8S Pro (S2882) V3.06
New features and Fixes :
* Corrected the BIOS datecode
* Updated ACPI S4 support
* Fixed an issue with Cherry Keyboards
* Fixed an issue with PXL-S30 SCSI Cards where the system
   would hang in the Option ROM
* Adjusted CPU temp detection method for more accurate
   CPU temperature display
* Updated CPU micro coding for new CPU support
* Updated the Sil3114 SATA Option ROM to v5.0.64

10/31/05
 

2882_305

TYAN  Thunder K8S Pro (S2882) V3.05
New features and Fixes :
* Added support for 4 Sec delay to the Power Button Mode
   options
* Fixed an issue where Opteron CPU's were not correctly
   displaying their temperatures
* Updated TSO support
* Added BCM F1 option for SMDC of LAN

09/07/05
 

2882_304

TYAN  Thunder K8S Pro (S2882) V3.04
New features and Fixes :
* Updated SMBIOS information
* Fixed an issue where the system will hang during the
   POST with both the Adaptec SO-DIMM 2015s Raid
   controller card and SMDC M3289 installed
* Fixed an issue where the Fan speed display would not
   register correctily if fan power control was set to enabled
* Updated BIOSCheck 2.4 support
* Updated CPU temperature display
* Added support for SMBIOS Type 38 IMPI information
* Updated PowerNow! support for CG stepping CPU's
* Updated the  boot loader console redirect support
* Changed PowerNow! minimal voltage to v1.35v
* Updated the lower FAN RPM registers for proper display
* Updated Opteron 254 PowerNow! support
* Updated IOMMU support

06/28/05
 

2882_303

TYAN  Thunder K8S Pro (S2882) V3.03
New features and Fixes :
* Fixed an issue where the Pepercon's USB KVM would hang
   in use
* Implemented AMD's recommendations for DDR400 speed
   settings when large loads (more than 4 dimms) were used
   at once
* Added a Auto detect feature and addded support for the
   M3289 & M3290 SMDC cards
* Implemented AMD erratum 123
* Added a IPMI Over Lan selectable option in the BIOS
   [82551]/[BCM5704]
* Fixed an issue where Bank Interleaving was not functioning
   properly
* Fixed an issue where AMD PowerNow! was not working
   correctly
* Fixed an issue where the reported values of CPU1 Vcore
   & CPU2 Vcore were not correct

05/04/05
 

2882_302

TYAN  Thunder K8S Pro (S2882) V3.02
New features and Fixes :
* Fixed the onboard Sil3114 SATA RAID driver rebooting in
   WinXP when a P2P bridge capable PCI card was installed
   (e.g. Osprey Video, ARC-1120 SATA Raid Card and etc.).
*
Note: Users have to change the PCI BUS scan order to see
   this change inacted
* Fixed an issue where the console sometimes can not
   receive data when in console redirect mode
* Adjusted the Auto Fan Speed Control behavior
* Implemented the AMD PowerNow! features
* Addressed an issue where Ex stepping were not being
   detected properly and the 1.0GHz HT link speed was not
   set correctly
* Addressed an issue where the DIMM memory size report
   was not accurate
* Fixed an issue where 4 RaidCore SATA Raid cards would
   hang during the POST at "Checking NVRAM.."

03/24/05
 

2882_301

TYAN  Thunder K8S Pro (S2882) V3.01
New features and Fixes :
* Fixed an issue where the intrusion siren alarm couldn't
   be cleared
* Added AMD PowerNow!™ Support
* Removed DRAM Power Control Feature
* Fixed an issue to correct memory size display while 4GB
   or above memory was installed
* Fixed an issue where unexpected machine-check errors
   would display

03/03/05
 

2882_300

TYAN  Thunder K8S Pro (S2882) V3.00
New features and Fixes :
* Updated the SiL3114 Option ROM to v5.0.48
* Updated CPU and NB modules to support D and Ex
   stepping CPU's
* Added Opteron 252 CPU support

01/04/05
 

2882_204

TYAN  Thunder K8S Pro (S2882) V2.04
New features and Fixes :
* Supports selection for endless BBS booting.
* Added Floppy B support
* Added support for "default boot order".  If BBS boot
   devices change, upon next power on the bios will revert
   to the default boot order to boot
* Upgraded SiL3114 Option ROM from v5.0.37 to 5.0.44
* Fixes PCI ZCR card hangs system during POST
* Add support for C0 + CG CPU mixing
* Fix up PME# can't be disabled issue.  Following "resume on
   PME#" of SETUP for PME enabled/disabled programming.
   Default changed to [enabled].
* Patch SMDC special case hang up issue
* Fix up 16 SATA HDD's connected to 2 3Ware cards booting
   fail issue

07/19/04
 

2882_203

TYAN  Thunder K8S Pro (S2882) V2.03
New features and Fixes :
* Updated PCI-X Interupt Routing
* Fixed an issue with the NetBench testing software
* Updated AMI Opteron Erratta # 109 and #110

06/01/04
 

2882_202

TYAN  Thunder K8S Pro (S2882) V2.02
New features and Fixes :
* Implemented memory remapping functions
* Updated SiL3114 Option ROM to v5.0.35
* Updated Remote Access Support
* Updated Fan Control
* Fixed DMI Type 18 Display
* Added Opteron 250 CPU Support

04/19/04
 

2882_201

TYAN  Thunder K8S Pro (S2882) V2.01
New features and Fixes :
* Updated AMI Core 9 to v8.00.010
* Fix the "up to 4GB" DRAM system unstable issue
* Updated Silicon Image Option ROM to v5.0.31
* Fixed Remote Console Redirect over SMDC issue
* Fixed entering Setup through SMDC issue
* Added support for SMDC COM port
* Updated DMI table

02/09/04
 

2882_102

TYAN  Thunder K8S Pro (S2882) V1.02
New features and Fixes :
* Fixed system hang up when using Adaptec cards
* Fixed a Console Redirection issue when using SMDC card
* Updated Option Rom for the Sil3114 to v5.0.24

10/08/03
 

2882_101

TYAN  Thunder K8S Pro (S2882) V1.01
New features and Fixes :
* SilImage 3114 op-rom update to 5.0.20
* Fixes DRAM size reporting error issue
* Auto Fan Speed Control support with [Disabled]/[Enabled]
* Added SMDC support

09/22/03
 

2882_100

TYAN  Thunder K8S Pro (S2882) V1.00
This is the first release BIOS. 

Information published on TYAN.com is subject to change without notice.
Copyright © 2006, TYAN COMPUTER CORPORATION. All Rights Reserved.