Thunder K8SE (S2892) BIOS

  Current BIOS Revisions

Definitions:

Boot Disk - Refers to either a Windows 95 or Windows 98 boot disk. Any other type of boot disk might load memory resident programs which will interfer with the flash process. Make sure you hit the F5 key when the boot disk first starts running to make sure no other programs are loaded in the back ground without your knowledge.

Bios Flash Package -  Unzip the entire bios package to a seperate clean floppy.  Insure there are 3 files that are unpacked during the unzip process

Requirements:

Two separate diskettes are needed. The first diskette is the Windows 95/98 Boot Disk. The second diskette should contain the 3 files needed to flash the bios.  These files are provided when you unzip the bios flash package from the website.

Procedure:

At the A: prompt simply type in "
flash" and the rest will be handled by the files included in your download.

Date

BIOS

Description

10/19/06
 

2892_203

TYAN  Thunder K8SE (S2892) V2.03
New features and Fixes :
* Added option in bios to scan Option ROM either by
   embedded device first or by Add-on card first
* Updated Option ROM placement process
* Fixed PCI-E PEG6 LAN card IRQ and shadow RAM resource
   conflict issue

07/12/06
 

2892_202

TYAN  Thunder K8SE (S2892) V2.02
New features and Fixes :
* Fixed an issue where some USB disks can't be detected
   properly
* Fixed a Post error that shows "Expansion ROM not initialized",
   if dual Highpoint 2220 Raid cards are used simultaneously
* Fixed an issue where the system would hang if one pressed
   the reset button too quickly
* Patched a LSI MegaRAID Option ROM fail issue if a keyboard
   is not also present
* Improved the reset button functionality

03/21/06
 

2892_201

TYAN  Thunder K8SE (S2892) V2.01
New features and Fixes :
* Fixed M7902 Option ROM initialize fails if an Intel Quad-Port
   Lan adapter is present
* Updated CPU Temp reporting
* Modify AutoFAN function terperature range ( 40'C ~ 60'C )
* Added BIOS setup item:  Onboard BCM(5704) LAN
   [Enable]/[Disabled].
* Added WatchDog function
* Added AMD Dualcore 285 CPU support
* Updated the nVidia Raid firmware to v5.50 for additional
   RAID 5 support

11/09/05
 

2892_200

TYAN  Thunder K8SE (S2892) V2.00
New features and Fixes :
* Updated nVidia nForce RAID ID support for nVidia chipset
   drivers v6.66 and higher
* Updated the LDT frequency settings for Ex stepping
   Opteron CPU's
* Added support for the M3291 SMDC Card

NOTE: If you are running a current OS installed with nVidia nForce driver v6.39 and bios version v1.03 (or earlier),  you will need to re-install your OS using at least nVidia nForce driver v6.66 and bios v2.00.

08/25/05
 

2892_103

TYAN  Thunder K8SE (S2892) V1.03
New features and Fixes :
* Added support for Rev E5/E6 Opteron CPU's
* Added AMD PowerNOW options w/ default setting as [Disabled]
* Added Auto Fan Control Function option for initial duty
   cycle from 25% to 55%
* Changed the Hot key for POPup BBS menu from [F8] to [F9]
* Added support for AMD BIOS check 2.3.0
* Added support for an AOPEN DVD1648/AAP drive
* Added support for nVidia SATA RAID mix with a regular
   SATA HDD
* Fixed an error where "CPU reading temperature error"
   would show during POST messages if you changed CPU's
* Added support to boot to an OS without a Keyboard present
* Added support for a LSI ultra 320 card to operate from a
   PCI-32 slot under 64 bit windows
* Added Broadcom LAN PXE boot option for port 1 or Port 2
* Added BIOS setup option for enable/disable the "POST
   errors" messages
* Added "IOMMU" setup option for Linux system
* Added "Memory clock" setup option

05/03/05
 

2892_101

TYAN  Thunder K8SE (S2892) V1.01
New features and Fixes :
This is the first release BIOS. 

Information published on TYAN.com is subject to change without notice.
Copyright © 2006, TYAN COMPUTER CORPORATION. All Rights Reserved.